====== Comandi per 123Solar ====== ====== Aurora ====== ===== Link ===== Autore [[http://www.curtronics.com/Solar/AuroraData.html|Curtronics]]\\ Download versione [[http://www.curtronics.com/Solar/ftp/aurora-1.9.0.tar.gz|1.9.0]] ===== Testare Aurora ===== aurora -a 2 -k 364 -Y 3 /dev/ttyUSB0 aurora -a 2 -p -n -f -g -m -v -Y3 /dev/ttyUSB0 ===== ===== ===== Aggiornamento manuale 123solar ===== [[https://github.com/jeanmarc77/123solar/wiki/2)-Help|https://github.com/jeanmarc77/123solar/wiki/2)-Help]] [[https://github.com/jeanmarc77/123solar/tree/7112dd3e549389eaaa799fd52796a5f786b36cfa|https://github.com/jeanmarc77/123solar/tree/7112dd3e549389eaaa799fd52796a5f786b36cfa]] ===== Manuale ===== v1.8.7 Uso: aurora [Opzioni] Device Opzioni: -A, --last-alarms Get last four alarms (once displayed FIFO queue is cleared) -b, --verbose Verbose mode. For maximum effectiveness should be the first option on the command line -C, --calc-value= Calculate monetary value using * kWh. ":$" is optional and if included the character(s) represented by the "$" will be used to denote monetary type in the output. Defaults to "$" -c, --columnize Output data in columns --> for -d, -e, -D, -3, -E, -t, & -T options only will disable any other options -- if value ends with an "*" reporting of that item may not be in inverters firmware -d , --get-dsp= Get DSP data indicates string to get data for. 0 indicates both 1 for only string 1, 2 for only string 2. is required for short option and is optional for long option and if omitted for long option data for both input strings will be retrieved -D, --get-dsp-extended Get more DSP data -3, --get-dsp-3phase Get 3-Phase DSP data -e, --get-energy Get Cumulated Energy readings (Excluding Central) -E , --get-energy-central= Get Cumulated Float Energy readings (Central&TRIO only) days 1 to 366 Default 366 is required for short option and optional for long option -f, --firmware-ver Query for Firmware Version string -g, --mfg-date Query for Inverter Manufacturing Date -h, --help This text -i, --get-count= Display Inverter Time Counters is required for short option is optional for long option and if omitted for long option then all counters will be displayed and Partial counter will be reset 1 = "Total Run Time" 4 = "Grid Connection Time" 2 = "Partial Run Time" 8 = "Reset Partial Run Time" -j, --get-joules Display Energy cumulated in the last 10 seconds -K, --use-kmult= Adjust vaules reported by -k, --daily-kwh by "" multiplier -k , --daily-kwh= Get past daily kWh for days (1-366) is required for short option and optional for long option and if omitted for long option then all 366 days or as many that are found will be displayed -L , --adjust-time= Automatically adjust the inverter time if it differs from the computer time. If is 0 (zero) do a Daylight Savings Time check. If is>= 1 change the inverter time if it differs by or more seconds. See the README for more information and constraints -l , --read-wait= Timeout for the read to the serial port. in 1/10ths seconds. Default is 1 (0.1 sec). See the README file for important information on this option -M , --max-runtime= Maximum amount of time in seconds that aurora will run trying to get data from the inverter -m, --get-conf Query for Inverter System Configuration -n, --serial-number Query for Inverter Serial Number -N , --central= Indicates Aurora Central ** Experimental ** 0 indicates Master, 1 indicates Slave -o, --output-file= Append data to file (Created if nonexistant) Note: If -c option is used only -d, -e, -D, -3, -E, -t, & -T options will output to file -O, --part-number-central Query for Inverter Part Number (Central only) -p, --part-number Query for Inverter Part Number -P , --comm-pause= Wait us between sending commands to inverter (1-1000000) -Q, --use-qmult Use inverter specific multiplier if known to adjust values reported by -q, --energy-sent -q , --energy-sent= Get past energy delivered to the grid ** Experimental ** in 10 second intervals for minutes (1-1440). is optional for long option and if omitted all data, ~24 hours worth will be reported. It is suggested the -Y option be used with this due to the extensive length of time this could take. See the README file for important information on this option -R , --read-timeout= Serial port read retry timeout value when reading a character from the Inverter (mS - minimum 200) See the README file for important information on this option -r, --calc-grid-power Calc Grid power using Grid Voltage * Grid Current, instead of reporting the Inverter's value. --> for -d option only, ignored when used with -c option (Inverter typically reports a lower value. This affects Inverter conversion efficiency value.) -S, --set-time Set Inverter Date/Time to system time -s, --get-state Get Inverter State -T, --get-loctime Display computer Date/Time -t, --get-invtime Display Inverter Date/Time -V, --version Aurora communications program version -v, --inv-version Query for Version string -U , --read-pause= Pause milli-seconds after sending command to inverter before reading response from inverter (1-10000) -u, --rpt-read-pause Report when/that pausing before read -W, --swap-endian Swap Endianness -w , --lock-wait= Seconds to wait to lock serial port. (1-30) -X, --rts-cts Enable RTS/CTS on the serial port. -x, --xon-xoff Enable XON/XOFF on the serial port. -Y , --retries= Retry failed communications with inverter up to times (1-100) -y, --rpt-retries Report the number of retires done Parametri obbligatori -a , --address= Inverter address. 1-31 on older inverters, 1-63 on newer inverters. Device Serial Device.